The Innokin Plexus Replacement Pods work with both the Innokin Plexus Pro and Plexus Go pod kits. Each pod holds 2ml of e-liquid and features a mesh coil available in three resistances: 0.6Ω dual mesh (Pro only), 0.8Ω, and 1.2Ω. The 0.6Ω option delivers warmer vapour for restricted DTL, the 0.8Ω suits RDTL vaping, whilst the 1.2Ω pod provides a tighter Mouth to Lung (MTL) draw closer to smoking.

Top-sliding fill design makes refills quick without removing the pod from your device. The transparent cylindrical chamber lets you monitor liquid levels at a glance. Pods come in packs of two and are designed to be replaced when flavour drops, typically after 5–7 days of regular use. Works best with 50/50 e-liquids or nic salts for proper wicking and throat hit.

Key Features

• Triple Resistance Options – 0.6Ω dual mesh for fuller vapour (Plexus Pro only), 0.8Ω for balanced RDTL, 1.2Ω for tight MTL. Pick based on your device and draw preference.

• Top-Sliding Refill – Slide the top cap to expose the fill port. Fits most e-liquid bottles, no need to remove the pod from your kit.

• Transparent Tank – 360° clear view lets you check liquid levels without guesswork. Refill before it runs dry to avoid burnt hits.

• Built-In Mesh Coils – Kanthal mesh heats evenly for clean flavour. Replace the entire pod when coil performance drops rather than fiddling with separate coil changes.

Core Advantages

Cross-Compatible Pod System

These pods fit both the Plexus Pro and Plexus Go kits, though the 0.6Ω dual mesh option is Pro-exclusive due to higher wattage requirements. The 0.8Ω and 1.2Ω pods work across both devices, so you're not locked into buying separate pod types if you own multiple Plexus kits.

Leak-Resistant Construction

The top-sliding fill mechanism creates a proper seal when closed, reducing leaks during carrying. The cylindrical design with 360° visibility also helps you spot potential flooding early. Vapers report minimal leaking when pods are filled correctly and not overfilled past the max line.

Optimised Mesh Coil Performance

Kanthal mesh structure provides larger surface area than traditional wire coils. You get fuller flavour extraction from your e-liquid, particularly noticeable on fruit and dessert blends. The 0.6Ω dual mesh option pushes this further with two heating elements for warmer, denser vapour production.

FAQs

Which resistance should I choose for my Plexus kit?

For the Plexus Pro, you can use all three resistances. The 0.6Ω dual mesh delivers warmer vapour at 25W for Restricted Direct to Lung. For the Plexus Go, stick to 0.8Ω (16W) or 1.2Ω (13W) as it can't power the 0.6Ω pod properly. Choose 1.2Ω for tighter MTL vaping, 0.8Ω for a slightly looser draw.

How long does each pod typically last?

Expect 5–7 days per pod with moderate use (100–150 puffs daily). Sweeter e-liquids or chain vaping can reduce that to 3–4 days. Replace the pod when flavour tastes muted or burnt. The built-in coil means you swap the whole pod rather than just the coil.

What e-liquid works best with these pods?

50/50 e-liquids or high-PG blends work well across all resistances. Nic salts between 10–20mg suit the 0.8Ω and 1.2Ω pods for smooth throat hit. The 0.6Ω dual mesh can handle slightly higher VG (60/40) due to larger wicking ports, though 50/50 remains the safest choice.

Can I clean and reuse these pods?

Not recommended. The built-in coil design means once it's burnt, rinsing won't restore performance. Some vapers rinse pods when switching flavours, but you're better off using a fresh pod to avoid lingering tastes and poor coil condition affecting your vape quality.

Why won't my pod fit properly in my device?

Check you're using the correct resistance for your kit. The 0.6Ω dual mesh pod only fits the Plexus Pro. If you're using a Plexus Go, stick to 0.8Ω or 1.2Ω pods. Also ensure the pod is fully inserted until you hear a click, and remove any protective seals before first use.